Subsonic Speed Calculator: Is Your Load Subsonic in This Weather?
Subsonic means slower than sound: about 1,116 fps in dry air at 59°F but only 1,051 fps at 0°F, so cold air can make a load supersonic.
In This Article
Last updated: November 19, 2026 · Originally published November 17, 2026
Enter your load’s velocity and the temperature where you are shooting below to see whether it stays subsonic, by how many feet per second, and how cold it would have to get before it cracks.
Subsonic speed at a glance
Most ammunition is designed to be supersonic, meaning the bullet leaves the muzzle traveling faster than the speed of sound (roughly 1,100–1,150 feet per second depending on conditions). That produces the familiar sharp “crack” you hear downrange as the bullet breaks the sound barrier. Subsonic loads, by contrast, are deliberately loaded so the bullet stays below that threshold which is typically with heavier projectiles pushed at lower velocities meaning no sonic crack is generated. The distinction is simple on paper, but it becomes critical once a suppressor enters the picture: a suppressor can effectively tame muzzle blast by trapping and cooling expanding gases, yet it has no effect on the shockwave a supersonic bullet creates in flight. Only staying subsonic removes that second, often louder, source of noise.
This is why many hunters pair subsonic ammunition with suppressors, especially for close-range work on game such as hogs or deer. The combination can drop the overall sound signature dramatically, often to levels that are far less likely to spook nearby animals, allow better follow-up shots on groups, and reduce the risk of hearing damage without relying solely on ear protection. Because the speed of sound itself changes with temperature, altitude, and humidity, a load that is reliably subsonic on a cool morning can creep over the threshold on a hot afternoon; a quick check against current weather conditions helps ensure you stay in the quiet zone where the suppressor can do its full job.
- The speed of sound in air depends on temperature. It falls by about 1.1 fps for every degree Fahrenheit the air cools.
- Altitude and air pressure do not change it on their own. Mountains matter only because the air up there is usually colder.
- Humidity adds a little speed, under 1% in all but hot, very humid air, so dry air is the cautious assumption.
- A 1,050 fps load has 66 fps of room at 59°F, 23 fps at 20°F, and goes supersonic just below 0°F.
- Box velocities come from the manufacturer’s test barrel. Your own chronograph reading is the number to trust.
Subsonic speed calculator: is your load subsonic at this temperature?
From the box, or better, your chronograph.
Use a minus sign for below zero.
Optional: humidity, elevation, safety cushion, common loads
Only changes the humidity term.
Set it to your chronograph’s spread.
The arithmetic
- Temperature: 20.0°F = (20.0 − 32) × 5/9 = −6.67°C; add 273.15 for kelvin: 266.48 K.
- Speed of sound in dry air (National Weather Service formula): 643.855 knots × √(266.48 ÷ 273.15) = 635.95 knots = 1,073.4 fps.
- Humidity: none entered, so dry air is used. Moist air is slightly faster, which only adds margin.
- Margin: 1,073.4 − 1,050 = 23.4 fps, which is 2.18% of the speed of sound (Mach 0.978).
- Crossover: sound slows to 1,050 fps at 273.15 × (1,050 ÷ 1,086.70)² = 255.0 K, which is −0.7°F (−18.1°C). Colder than that, this load is supersonic.
Sources: NWS speed of sound, NASA Glenn.
The same load on warmer and colder days
| Air | Sound (fps) | Margin (fps) | Verdict |
|---|---|---|---|
| −10°F (−23°C) | 1,039 | −11 | Supersonic |
| 0°F (−18°C) | 1,051 | 1 | Inside cushion |
| 10°F (−12°C) | 1,062 | 12 | Inside cushion |
| 20°F (−7°C) | 1,073 | 23 | Inside cushion |
| 30°F (−1°C) | 1,084 | 34 | Inside cushion |
| 40°F (4°C) | 1,096 | 46 | Inside cushion |
| 50°F (10°C) | 1,106 | 56 | Subsonic |
The velocity is the number you entered. A box velocity was measured in the manufacturer’s test barrel; your barrel and the temperature of the ammunition itself can change it, so a chronograph reading from your own gun on the day is the number to trust.
Get the Popular Suppressors newsletter. Suppressor news, NFA updates and the tools on this site. The answer above was never held back for it. Sign up free.
This calculator runs in your browser. It sends nothing and stores nothing.
How the subsonic speed calculator works
A bullet is subsonic when it flies slower than sound travels through the air around it. So the calculator answers two questions: how fast is sound moving through the air you are shooting in, and how far below that is your load?
- It turns your temperature into kelvin. Physics works on an absolute scale, where zero means no heat at all. Kelvin is Celsius plus 273.15.
- It works out the speed of sound in dry air. It uses the National Weather Service formula, which needs only the temperature.
- It adds the small humidity effect, if you enter one. Moist air carries sound slightly faster, so leaving humidity blank gives the cautious answer.
- It subtracts your velocity. What is left is your margin. It also solves the formula backward to find the temperature at which sound would slow down to your load’s speed.
speed of sound (knots) = 643.855 × √(T ÷ 273.15), T in kelvin
1 knot = 1.68781 fps, so at 0°C (32°F) sound travels 1,086.7 fps
margin = speed of sound − muzzle velocity
goes supersonic below T = 273.15 × (velocity ÷ 1,086.7)²
The National Weather Service formula is the same physics NASA’s Glenn Research Center teaches as a = √(γRT): the speed of sound equals the square root of the gas’s specific heat ratio (how much its temperature jumps when it is squeezed) times its gas constant times its absolute temperature. For air, the first two are fixed, so temperature is the only thing left to change.
Worked example. One factory 190-grain subsonic .300 Blackout load is listed at 1,050 fps from a 16-inch test barrel. On a 20°F morning:
- 20°F is −6.67°C, which is 266.48 kelvin.
- 643.855 × √(266.48 ÷ 273.15) = 635.95 knots, which is 1,073.4 fps.
- 1,073.4 − 1,050 = 23.4 fps of margin, or 2.2% of the speed of sound.
- 273.15 × (1,050 ÷ 1,086.7)² = 255.0 kelvin, which is −0.65°F. Below that, the load is supersonic.
So the load is still subsonic at 20°F, but by less than the default 50 fps cushion. The calculator flags it as inside the cushion. On a 59°F day the same load has 66 fps to spare.
Why temperature sets subsonic speed and altitude does not
The speed of sound isn’t a fixed number like 1,125 feet per second. It changes mainly with the temperature of the air. Warmer air lets sound (and a bullet’s shockwave) travel a little faster; colder air slows it down. That’s why a load that stays safely subsonic on a 40-degree morning can tip over the line on a 90-degree afternoon even though nothing else about the ammo or rifle changed.
Altitude by itself doesn’t set the speed of sound. Thin air at elevation and thick air at sea level behave the same for this purpose as long as the temperature is identical. What usually happens is that the air gets colder as you go higher, and that colder temperature is what lowers the speed of sound. On any given day the thermometer is the number that matters most. Once you know the actual air temperature where you’re shooting, you know the real subsonic threshold for that moment—altitude is just background information.
How much humidity changes the speed of sound
Humidity does affect the speed of sound, but only a little. Water vapor is lighter than the nitrogen and oxygen that make up most of the air, so humid air is slightly less dense than dry air at the same temperature. Because sound travels a bit faster through that lighter mixture, higher humidity raises the speed of sound by a small amount, typically just a few feet per second even when the air is very moist.
Compared with temperature, the humidity effect is minor. A big swing in relative humidity (say from bone-dry to near 100 %) usually moves the speed of sound less than a modest temperature change of a couple of degrees. For deciding whether a load stays subsonic, the thermometer is still the main tool. Humidity is worth a quick glance if you’re already right on the edge and the air feels especially damp, but it almost never flips a load from subsonic to supersonic on its own.
Where subsonic loads get into trouble
- Cold mornings. Every 10°F colder takes about 11 fps off the speed of sound. A load with 66 fps of room on a 59°F day has about 23 fps at 20°F.
- Loads built close to the line. A common standard-velocity .22 LR is listed at 1,070 fps. That is subsonic at 59°F by 46 fps, has 3 fps left at 20°F, and is supersonic below 17°F. A subsonic .22 LR hollow point, listed at 1,050 fps, keeps a 20 fps larger margin.
- A different barrel from the manufacturer’s. A common 147-grain 9mm load is listed at 1,000 fps from a 4-inch test barrel. Fired from a carbine or a long pistol barrel it can run faster. Measure it in your gun.
- Ammunition temperature. The temperature of the powder changes how hard it pushes. Ammunition left in a hot truck or a cold one may not match the box. A chronograph at the bench settles it.
- Shot-to-shot spread. No two rounds leave at exactly the same speed. The safety cushion is there for that. Our default is 50 fps; that is our own starting point, not a published standard. Set it to the gap between your slowest and fastest shot over a chronograph.
Speed of sound by temperature: reference table
Every number below was computed with the National Weather Service formula and, for the humid columns, Bohn’s humidity method. Dry air is the cautious column: if your load is under that number, humidity can only add room.
| Air temperature | Celsius | Dry air (fps) | Dry air (m/s) | 100% humidity, sea level (fps) | 100% humidity, 5,000 ft (fps) |
|---|---|---|---|---|---|
| −20°F | −28.9°C | 1,028 | 313.2 | 1,028 | 1,028 |
| −10°F | −23.3°C | 1,039 | 316.8 | 1,039 | 1,039 |
| 0°F | −17.8°C | 1,051 | 320.3 | 1,051 | 1,051 |
| 10°F | −12.2°C | 1,062 | 323.7 | 1,063 | 1,063 |
| 20°F | −6.7°C | 1,073 | 327.2 | 1,074 | 1,074 |
| 30°F | −1.1°C | 1,084 | 330.6 | 1,085 | 1,086 |
| 40°F | 4.4°C | 1,096 | 333.9 | 1,097 | 1,097 |
| 50°F | 10.0°C | 1,106 | 337.2 | 1,109 | 1,109 |
| 60°F | 15.6°C | 1,117 | 340.5 | 1,120 | 1,121 |
| 70°F | 21.1°C | 1,128 | 343.8 | 1,132 | 1,133 |
| 80°F | 26.7°C | 1,139 | 347.0 | 1,145 | 1,146 |
| 90°F | 32.2°C | 1,149 | 350.2 | 1,158 | 1,160 |
| 100°F | 37.8°C | 1,159 | 353.4 | 1,172 | 1,174 |
| 110°F | 43.3°C | 1,170 | 356.5 | 1,187 | 1,190 |
Popular subsonic loads and the temperature where each one cracks
The velocities below were read from each manufacturer’s own product page on October 27, 2026. Where the page lists a test barrel length, it is shown. The margin and crossover columns are our arithmetic in dry air, which is the cautious case.
| Caliber | Load (manufacturer’s page) | Listed velocity (fps) | Test barrel | Margin at 59°F (fps) | Margin at 20°F (fps) | Supersonic below |
|---|---|---|---|---|---|---|
| .22 LR | Standard velocity, 40 gr lead round nose | 1,070 | Not listed | 46 | 3 | 17.0°F |
| .22 LR | Subsonic, 40 gr lead hollow point | 1,050 | Not listed | 66 | 23 | −0.7°F |
| .22 LR | Extra-quiet, 40 gr lead round nose | 710 | Not listed | 406 | 363 | Colder than any weather |
| 9mm Luger | 147 gr full metal jacket | 1,000 | 4 in. | 116 | 73 | −43.3°F |
| .45 Auto (ACP) | 230 gr full metal jacket | 890 | 5 in. | 226 | 183 | Colder than any weather |
| .300 Blackout | Subsonic, 190 gr expanding | 1,050 | 16 in. | 66 | 23 | −0.7°F |
| .300 Blackout | Suppressor load, 220 gr open tip match | 1,000 | Not listed | 116 | 73 | −43.3°F |
Two loads at the same listed speed, the 190-grain subsonic .300 Blackout and the subsonic .22 LR hollow point, share the same crossover: just below 0°F. The physics does not care about caliber. Only velocity and air temperature decide it. For a deeper look at the .300 Blackout loads themselves, our sister site Popular Ammo covers 300 Blackout supersonic and subsonic loads side by side.
What this calculator does not cover
- Barrel length corrections. We could not find a published figure, from a manufacturer or a standards body, for how many fps a subsonic load gains or loses per inch of barrel. So the calculator does not guess. Chronograph your load in your gun.
- Ammunition temperature. Powder burns differently hot and cold, and manufacturers do not publish one figure that fits every load. Again, the chronograph settles it.
- The bullet in flight. A bullet slows after it leaves the muzzle, so a load that starts subsonic stays subsonic. The calculator checks the muzzle, which is where it matters.
- How loud the shot is. Staying subsonic removes the bullet’s crack. The muzzle blast and the action still make noise, and that depends on the suppressor and the gun.
- Extreme humidity below freezing. The humidity term uses the vapor pressure over water. Below freezing it adds 2 fps or less, even at 15,000 feet, so it barely moves any answer.
Where the numbers come from
- Speed of sound formula: National Weather Service, speed of sound calculator and its formula sheet (643.855 knots × √(T ÷ 273.15)).
- The physics behind it: NASA Glenn Research Center, Speed of Sound (a = √(γRT)).
- Humidity and pressure: Dennis A. Bohn, “Environmental Effects on the Speed of Sound,” Journal of the Audio Engineering Society, Vol. 36, No. 4, April 1988. It also gives the measured 331.45 m/s in dry air at 0°C; our formula gives 331.23 m/s, within 0.07%.
- Water vapor and air pressure: National Weather Service vapor pressure and pressure altitude formulas.
- Load velocities: the manufacturer’s product page for each load, linked in the table, read October 27, 2026.
New to quiet shooting? Start with our subsonic ammo guide for suppressors, then see how much quieter subsonic is than supersonic. Our quietest suppressor by caliber rankings and the suppressor comparison chart cover the can itself.
The Ruger 10/22 wins at 47%, with .22 pistols at 32% and bolt-action .22s at 19%.
Frequently asked questions
What fps is subsonic?
Any speed below the speed of sound at the air temperature you are shooting in. That is about 1,116 fps at 59°F, 1,073 fps at 20°F and 1,051 fps at 0°F, in dry air.
Does altitude change the speed of sound?
Not by itself. Lower pressure and lower density cancel out. Only the temperature changes it, and high places are usually colder, which is why altitude seems to matter.
Why does my subsonic ammo crack in cold weather?
Cold air carries sound more slowly, about 1.1 fps slower for each degree Fahrenheit. A load listed at 1,050 fps goes supersonic just below 0°F, and a 1,070 fps load below 17°F.
Is 1,050 fps subsonic?
Yes, in dry air at any temperature above −0.7°F. At 20°F it has only 23 fps of room, so check it with a chronograph before a cold hunt.
Does humidity matter for subsonic ammo?
Very little. Humid air carries sound slightly faster, by under 1% in all but hot, very humid air. Leaving humidity out gives the cautious answer.
